Motorola Cm300 User Manual10/27/2022 ![]() ![]()
Repeat Step 5, except do so while speaking into the microphone.Motorola cm300d service manual By Jon Green Follow | Public Not start to move while NOT speaking into the microphone. Just far enough to stop the vehicle motion completely. Then, set the vehicle transmission selector to DRIVE. Press the vehicle brake pedal firmly and repeat Steps 1 and 2.Įnsure that there is a minimum of two vehicle lengths between the front of the vehicle and any object in Press the vehicle brake pedal slightly just enough to illuminate the vehicle brake light(s). Repeat Step 1, except do so while speaking into the microphone. While NOT speaking into the microphone, verify that thereĪre no unusual effects (visual or audible) to the vehicle lights, or other electrical equipment and accessories. Pedal completely and key the radio transmitter. Run the vehicle engine at idle speed and set the vehicle transmission selector to PARK. The following procedure checks for the mostĬommon types of interference that may be caused by a radio transmitter to a vehicle braking system: Never activate the radio transmitter while the vehicle is in motion and the vehicle trunk lid is open.īe sure the following vehicle testing is done in an isolated area. Modular unit and associated braking system wiring. Route all radio wiring, including the antenna transmission line, as far away as possible from the braking #MOTOROLA CM300 USER MANUAL INSTALL#If the braking modular unit is located on the left side of the vehicle, install the radio on the right side of the If you cannot determine the location of the braking modulator unit, refer to the vehicle service manual or contact a dealer for the particular make of the vehicle. Unit may be located in the trunk, under the dashboard, in the engine compartment, or in some other cargoĪrea. Depending on the make and model of the vehicle, the braking modulator Before installing the radio, determine the location of the braking modulator unit in the vehicle. The operation of the vehicle braking system.Īlways provide as much distance as possible between the braking modulator unit and the radio, the radioĪntenna, and associated transmission line. System test procedures to ensure that the radio, when transmitting, does not interfere with Motorola recommends the following radio installation precautions and vehicle braking Refer to your vehicle service manual for your vehicle’s braking system, or contact yourĭisruption of the anti-skid/anti-lock braking system by the radio transmitter may result in The following installation suggestions and test procedures are recommended for vehicles with electronic antilock/anti-skid brakes. Publication part number 68P81095C99) to ensure compliance with Radio Frequency (RF) energy exposure.įor a list of Motorola-approved antennas and other accessories, visit the following web site which listsĪpproved accessories for your radio model. Operating instructions in the Product Safety and RF Exposure booklet enclosed with each radio (Motorola Be sure that Product Safety and RF Safety Booklet enclosed with this radio is available to the end user uponĬompletion of the installation of this radio.īefore using this product, the operator must be familiar with the RF energy awareness information and.Be sure that antenna installation is per Chapter 4 of this manual.Install only Motorola approved antennas and accessories. ![]() To ensure compliance to RF Energy Safety standards: NOT authorized for general population, consumer, or any other use. Of their exposure and can exercise control over their exposure to meet FCC limits. #MOTOROLA CM300 USER MANUAL FULL#This radio is intended for use in occupational/controlled conditions, where users have full knowledge WITH RADIO FREQUENCY (RF) ENERGY EXPOSURE Operation of a Conventional Ignition SystemĨ.1 Introduction. Removing the Radio from the Mounting Frame. Inserting the Radio into the Mounting Frame (Figure 5.1). Installing the Mounting Frame into the Dashboard. 8Ĥ.2 Selecting an Antenna Site/Location on a Metal Body Vehicle. 5Ĥ.1 Antenna Installation and Compliance with Radio Frequncy 2ģ.1 Planning the Mounting Trunnion Installation. 1Ģ.1 Planning the Power Cable Installation. iiiĮlectronic Anti-Lock/Anti-Skid Brakes. Installation Requirements for Compliance with Radioįrequency (RF) Energy Exposure Safety Standards. MOTOROLA, the Stylized M Logo, and Radius are registered in the US Patent & Trademark Office.Īll other product or service names are the property of their respective owners. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |